Remote Job Launching via ICE with VirtualBox VMs
This guide will walk you through how to set up a VirtualBox virtual machine (VM) running Fedora Linux—running on top of a Mac OS X host—to use as a compute resource during remote job launches. Other flavors of Linux may require slightly different steps.
The user must have ICE and its associated dependencies installed before moving forward. See Getting ICE for more details.
The user must also install a VM software. Oracle's VirtualBox is used for this tutorial. See the VirtualBox download page for more details.
The VM itself also requires an operating system, and the Fedora Linux distribution was installed on the VM for the purpose of this tutorial.
On the Host Machine
Linux/Mac OS X Hosts
First, add yourself to the vboxusers group by running the following line in a terminal: sudo usermod -aG vboxusers <your username>
You may have to add vboxdrv, vboxnetadp, and vboxflt to your kernel modules. To do so you will create a new file in /etc/modprobe.d using the following commands:
sudo nano /etc/modprobe.d/virtualbox
ctrl + shift + v to paste the following lines into the file:
Once done, press
ctrl + x then
y to save the file. Once this step is complete, reboot your host system.
Once the host system has rebooted, start VirtualBox, but do start the VM.
Instead, in VirtualBox navigate to
File > Preferences > Network > Host Only and hit the add button. This should add a network named
To confirm, execute
ifconfig in a terminal and check that
vboxnet0 is listed in the output of the command.
Back in VirtualBox, highlight the VM and go to
Settings > Network > Adapter 2 > Host-Only vboxnet0.
Now you can start your VM and proceed to the Inside the VM section.
Start VirtualBox, but not the VM. Select your VM from the list and go to
Settings > Network > Adapter 2 and select Bridged Adapter from the list. Start the VM and proceed to the next section.
Inside the VM
Once you have your host OS set up and your VM started up you can open a terminal to finish the setup.
If you do not have a password set up do so with:
You will also have to make sure that you have `sshd` running on the VM. To do so on Fedora issue the command:
sudo systemctl enable sshd.service
Then, you will need to determine the ip address that will be used to connect from the host to the VM. To find this out issue the command:
The output will look something similar to the following:
lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536 inet 127.0.0.1 netmask 255.0.0.0 inet6 ::1 prefixlen 128 scopeid 0x10<host> loop txqueuelen 0 (Local Loopback) RX packets 14 bytes 1400 (1.3 KiB) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 14 bytes 1400 (1.3 KiB) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 p2p1: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500 inet 10.0.2.15 netmask 255.255.255.0 broadcast 10.0.2.255 inet6 fe80::a00:27ff:fe71:e5d2 prefixlen 64 scopeid 0x20<link> ether 08:00:27:71:e5:d2 txqueuelen 1000 (Ethernet) RX packets 21 bytes 2844 (2.7 KiB) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 39 bytes 6216 (6.0 KiB) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 p7p1: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500 inet 192.168.56.101 netmask 255.255.255.0 broadcast 192.168.56.255 inet6 fe80::a00:27ff:febd:8a04 prefixlen 64 scopeid 0x20<link> ether 08:00:27:bd:8a:04 txqueuelen 1000 (Ethernet) RX packets 3 bytes 1240 (1.2 KiB) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 22 bytes 4730 (4.6 KiB) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
The ip address you want is listed next to
inet on the last entry.
For Windows Hosts
There is an additional step for those running a Windows host. In your VM terminal issue these two commands:
sudo dhclient -r sudo dhclient
And then reboot the VM.
Back on the Host Machine
Finally, on your host machine (while you still have the VM active) open ICE and prepare your favorite job. When you have reached the job launch phase you can enter the ip address that was found in the previous section under the hostname section of the launcher form. When you go to launch the job you will be prompted to enter the username and password for the VM. Do so and your job will be launched on the VM. Once the job is complete the relevant data will automatically be passed back to your host machine via ICE.