EGL provides general statements such as if and while, as well as action statements for accessing data sources or invoking external logic.
The case statement responds to conditions at run time by executing one set of statements rather than another:
- You can test a criterion value. The following example invokes
function test() x Int = 3; case (x) when (1) myFirstFunction(); when (2, 3, 4) mySecondFunction(); otherwise myDefaultFunction(); end end
- You can test a set of logical expressions. The following example displays only "x passes":
function test() x Int = 3; y Int = 5; z Int = 7; case when (x == 3) SysLib.writeStdOut("x passes"); when (y == 5) SysLib.writeStdOut("y passes"); when (z == 7) SysLib.writeStdOut("z passes"); otherwise SysLib.writeStdErr("You will not see this message."); end end end
As shown, no more than one clause ever executes. Control does not “fall through” from one clause to the next.
The EGL continue statement returns control to the start of a block of code controlled by a for, forEach, or while statement. The statement lets you return to a labeled statement of one of those kinds, or to the nearest embedding statement of one of those kinds.
The following example assumes that you have coded a print function named printReport.
for (i from 1 to 100 by 1) printReport(myList[i]); if ((i % 10) != 0) continue; end // if printReport(blankLine); end // for
That code prints the members of a list, inserting a blank line between each group of ten.
The EGL exit statement exits from a function, program, service, or run unit; or from a block of code controlled by a case, for, forEach, if, or while statement.
The for statement runs a set of statements in a loop that repeats until a counter reaches a specified value.
The example code shows three variations of a for statement that adds the same set of numbers.
program MyTestProgram function main() inputList int =[10, 4, 6, 8, 2]; numberInList int = inputList.getSize(); sum = 0; // the first for loop increments by 1. for(i int from 1 to numberInList) sum = inputList[i] + sum; end SysLib.writeStdOut("sum after the first for loop is " + sum); sum = 0; // the second for loop has the same effect but specifies the increment value. for(i int from 1 to numberInList by 1) sum = inputList[i] + sum; end SysLib.writeStdOut("sum after the second for loop is " + sum); sum = 0; // the third for loop starts at the opposite side of the list and decrements by 1 for(i int from numberInList to 1 decrement by 1) sum = inputList[i] + sum; end SysLib.writeStdOut("sum after the third for loop is " + sum); end end
The following code has If statements embedded in other If statements.
program MyTestProgram // A binary search finds a value in a sorted (preferably short) list. function binarySearch(list int, lowIndex int, highIndex int, value int) returns(int) while(true) middleIndex int = (lowIndex + highIndex) / 2; if(list[middleIndex] == value) return(middleIndex); else if(list[middleIndex] >= value) highIndex = middleIndex - 1; else if(list[middleIndex] < value) lowIndex = middleIndex + 1; end end end if(highIndex < lowIndex) return(-1); end end end function main() myNumbers int =[-6, -1, 2, 4, 7, 9 ]; valueOfInterest int = -1; lowestIndex int = 1; highestIndex int = myNumbers.getSize(); location int = binarySearch(myNumbers, lowestIndex, highestIndex, valueOfInterest); if (location == -1) SysLib.writeStdOut("Did not find " + valueOfInterest + "."); else SysLib.writeStdOut("The value of interest is " + valueOfInterest + ", at location " + location + "."); end end end